Shrink-fit assembly temperature
API · /pressfit-api
Press Fit API
healthy
3,435 Subscribers
Interference (press and shrink) fit engineering maths as an API, computed locally and deterministically from the Lamé thick-wall equations — the contact-pressure, holding-capacity and assembly-temperature numbers a mechanical designer or machinist sizes a shaft-and-hub joint with. The pressure endpoint gives the contact pressure that builds at the interface from the diametral interference, the shaft and hub diameters and the elastic modulus, plus the tensile hoop stress at the hub bore — the highest stress in the joint, which a thin hub can split if it exceeds the yield: a 50 mm solid steel shaft in a 100 mm hub with 0.05 mm interference makes about 75 MPa of contact pressure and 125 MPa of bore hoop stress, and doubling the interference doubles the pressure. The holding endpoint turns that pressure into the axial push-out force and the transmissible torque through the friction at the interface (force = pressure × contact area × friction, torque = force × shaft radius), the figures that decide whether the joint slips under load. The assembly-temperature endpoint gives the heating (hub) or cooling (shaft) temperature change for a shrink fit — ΔT = (interference + clearance) ÷ (α × diameter) — so the part slides on freely and grips as it returns to temperature. Everything is computed locally and deterministically, so it is instant and private. Ideal for mechanical-design and machine-building tools, manufacturing and CAD utilities, and engineering calculators. Pure local computation — no key, no third-party service, instant. Same-material Lamé estimates — verify against the material yield with a safety factor. 3 compute endpoints. For thin-wall pressure-vessel stress use a pressure-vessel API.
api.oanor.com/pressfit-api
API health
healthy- Uptime
- 100.00%
- Server probes · 24h
- Avg latency
- 74 ms
- Server probes · 24h
- Subscribers
- 3,435
- active
- Total calls
- 80
- last 7 days
Pricing
Pick a tier — billed monthly, cancel anytime.
Free
Free
- 4,200 calls / month
- 2 requests / second
- Hard cap (429 above quota, no overage)
- 4,200 calls/month
- 2 req/sec
- Pressure + holding + assembly temp
- No credit card
Starter
€13.30 /month
- 47,000 calls / month
- 6 requests / second
- Hard cap (429 above quota, no overage)
- 47,000 calls/month
- 6 req/sec
- Lamé pressure, torque & hoop stress
- Email support
Pro
€40.50 /month
- 205,000 calls / month
- 15 requests / second
- Hard cap (429 above quota, no overage)
- 205,000 calls/month
- 15 req/sec
- Mechanical-design & CAD pipelines
- Priority support
Mega
€124.00 /month
- 1,090,000 calls / month
- 40 requests / second
- Hard cap (429 above quota, no overage)
- 1,090,000 calls/month
- 40 req/sec
- Manufacturing-scale
- Dedicated SLA
Built by
Related APIs
Other APIs with overlapping tags.
Riveted Joint API
Riveted-joint strength maths as an API, computed locally and deterministically — the shear, bearing and rivet-count numbers a structural, sheet-metal or aircraft fitter checks a riveted connection by. The shear-capacity endpoint gives the load a rivet group carries across its shanks = the rivet area (π/4·d²) × the shear strength × the number of rivets × the shear planes — a rivet in single shear is cut on one plane, in double shear (the centre plate of a butt joint with cover plates) on two, so it carries twice. The bearing-capacity endpoint gives the load the rivets can press against the sides of their holes before the plate crushes = the projected contact area (diameter × plate thickness) × the bearing strength × the number of rivets; thin plates fail in bearing long before the rivet shears, which is exactly why both must be checked — the joint strength is the lesser of the two. The rivets-required endpoint inverts it: the rivets a design load needs = the load ÷ the allowable load per rivet (area × allowable shear × planes), rounded up to a whole rivet, using the working shear (strength ÷ safety factor) not the raw value. Everything is computed locally and deterministically, so it is instant and private. Ideal for structural and sheet-metal estimating, mechanical-design and fastener tools, and engineering calculators. Pure local computation — no key, no third-party service, instant. Shank-shear and bearing only — also confirm edge tear-out and minimum pitch. 3 compute endpoints. For bolt preload and torque use a bolt-torque API; for thread geometry a thread API; for welded joints a welding API.
api.oanor.com/rivet-api
Winch Drum API
Winch and cable-drum maths as an API, computed locally and deterministically — the rope-capacity, line-pull and rope-out numbers a winch operator, rigger or recovery driver works a drum with. The capacity endpoint gives the rope a drum holds by exact layer geometry: the sum over every full layer of the turns per layer × π × that layer's mean wrap diameter, where turns per layer = drum width ÷ rope diameter and the number of layers = the flange-to-barrel depth ÷ rope diameter — a 10-inch barrel, 20-inch flange, 12-inch-wide drum on half-inch rope holds about 940 ft over 10 layers. The layer-pull endpoint shows why pull falls as the drum fills: the rated pull is for the bare-drum first layer, and as rope piles on, the growing lever arm cuts the line pull and raises the line speed in the same ratio — pull × (first-layer diameter ÷ this layer's diameter) — so the top layer of a deep drum can pull barely half the bottom-layer rating, which is why you spool off to bare drum for a hard pull or add a snatch block. The length-at-layer endpoint gives the rope wound after a number of full layers, for marking the rope or knowing how much line is out. Everything is computed locally and deterministically, so it is instant and private. Ideal for winch- and hoist-sizing tools, recovery and off-road apps, marine and industrial-rigging utilities, and engineering calculators. Pure local computation — no key, no third-party service, instant. Geometric estimate — allow for nesting and freeboard. 3 compute endpoints. For capstan friction use a capstan API; for block-and-tackle a pulley API.
api.oanor.com/winch-api
Elevator Traction API
Traction-elevator engineering maths as an API, computed locally and deterministically — the counterweight, hoist-motor and rope-traction numbers a lift engineer or building-services designer sizes a passenger elevator with. The counterweight endpoint gives the balancing mass = the empty car plus a fraction of the rated load (the overbalance, typically 40–50 %, 45 % common), so a 1,000 kg car rated for 1,000 kg uses a 1,450 kg counterweight — the car and weight balance near half load and the machine is sized for the worst-case imbalance, not the full load. The motor-power endpoint uses that: because the counterweight cancels most of the car, the motor only lifts the out-of-balance load = rated load × (1 − overbalance), so power = that × g × speed ÷ efficiency (~65–75 % geared) — a 1,000 kg lift at 1.5 m/s needs only about 11–12 kW, half what a counterweight-less hoist would draw. The traction-ratio endpoint checks the friction grip: a traction elevator moves the ropes by friction over the sheave, so the available traction (e^(μθ), the capstan equation) must beat the T1/T2 tension ratio at both worst cases — a full car at the bottom and an empty car at the top — and it returns the governing ratio. Everything is computed locally and deterministically, so it is instant and private. Ideal for lift-design and building-services tools, vertical-transport and MEP utilities, and engineering calculators. Pure local computation — no key, no third-party service, instant. Sizing estimates — follow the lift code and maker data. 3 compute endpoints. For block-and-tackle use a pulley API; for capstan friction a capstan API.
api.oanor.com/elevator-api
HVAC Air-Side Load API
HVAC air-side heat maths as an API, computed locally and deterministically with the classic standard-air factors — the sensible, latent and airflow numbers a mechanical engineer or HVAC technician sizes ducts and equipment with. The sensible endpoint gives the sensible heat an airflow carries to change temperature: Qs = 1.08 × CFM × ΔT (dry-bulb difference), where the 1.08 bundles standard-air density and specific heat — 2,000 CFM across a 20 °F difference is 43,200 BTU/hr, 3.6 tons — with the result in BTU/hr, tons and kW. The latent endpoint gives the latent (moisture) heat: Ql = 0.68 × CFM × ΔW, where ΔW is the humidity-ratio difference in grains of water per pound of dry air, the dehumidification part of a cooling load that runs high in humid climates and from people and cooking, and why air conditioners are sized on total, not just temperature. The airflow endpoint inverts the sensible relation: CFM = sensible load ÷ (1.08 × ΔT), the supply air needed at a chosen supply-to-room temperature difference (comfort cooling runs ~18–22 °F below room), the number that sets fan and duct size — sanity-checked against ~400 CFM per ton. Everything is computed locally and deterministically, so it is instant and private. Ideal for HVAC-design and load-calc tools, mechanical-estimating and commissioning utilities, and building-engineering apps. Pure local computation — no key, no third-party service, instant. Standard-air factors — adjust for altitude. 3 compute endpoints. For room rule-of-thumb sizing use an HVAC API; for moist-air properties a psychrometric API; for duct sizing a ductwork API.
api.oanor.com/hvacload-api
Frequently asked questions
Quick answers about pricing, quotas, and integration.
How do I get an API key for Press Fit API?
Sign up for free at oanor.com, generate an API key from the developer dashboard, and call Press Fit API with the x-oanor-key header. No credit card needed for the free tier.
What's the rate limit for Press Fit API?
Free tier allows 1 request per second. Paid plans scale up to 50 requests per second on the Mega tier. Hard limits return HTTP 429 above the quota — no surprise overage charges.
How much does Press Fit API cost?
Press Fit API has a free tier with 100 calls / month. Paid plans start at €13.30 / month with higher quotas and faster rate limits.
Can I cancel my subscription anytime?
Yes. Plans are billed monthly and you can cancel anytime from your billing dashboard. No long-term contracts and no cancellation fee.
Is Press Fit API GDPR-compliant?
All requests to Press Fit API go through our EU-based gateway. Your upstream API key never leaves our server and no personal data is shared with the upstream provider beyond the request you send.
Pick an endpoint from the list on the left to see its details and try it.
Code snippets
Sign up to get an API key, then call any path under your slug.
curl https://api.oanor.com/pressfit-api/SOME_PATH \
-H "x-oanor-key: oanor_test_..."const res = await fetch("https://api.oanor.com/pressfit-api/SOME_PATH", {
headers: { "x-oanor-key": "oanor_test_..." }
});
const data = await res.json();$ch = curl_init("https://api.oanor.com/pressfit-api/SOME_PATH");
curl_setopt($ch, CURLOPT_RETURNTRANSFER, true);
curl_setopt($ch, CURLOPT_HTTPHEADER, ["x-oanor-key: oanor_test_..."]);
$response = curl_exec($ch);import requests
r = requests.get(
"https://api.oanor.com/pressfit-api/SOME_PATH",
headers={"x-oanor-key": "oanor_test_..."},
)
print(r.json())Ratings
Sign in to rate.
No reviews yet.
Discussion
Ask questions, share usage tips, get answers from the provider and other developers. Public — anyone can read.
Sign in to start a thread or reply.
Sign inNew thread
📌 Pinned
🔒 Locked
·
·
·
-
Provider answer
🔒 This thread is locked — no new replies.
-
·
- No threads yet — start the discussion.
Support
Private 1:1 support with the provider — billing questions, integration issues, account problems. Only you and the provider team can see these threads.
Sign in to open a support ticket.
Sign inOpen new ticket
Describe what you need help with. The provider team gets an email and replies on the ticket page.
-
·
Urgent - No tickets yet for this API.